DatasheetsPDF.com

UPB586G Dataheets PDF



Part Number UPB586G
Manufacturers NEC
Logo NEC
Description 3.0 GHz PRESCALER DIVIDED BY 256/ 128/ 64 FOR BS/CS TUNER
Datasheet UPB586G DatasheetUPB586G Datasheet (PDF)

www.DataSheet4U.com 2.5 GHz DIVIDE- BY- 512/256 PRESCALER FEATURES • HIGH FREQUENCY OPERATION TO 2.5 GHz • WIDE BAND OPERATION • SINGLE SUPPLY VOLTAGE: VCC = 5 V ±10% • AVAILABLE IN TAPE AND REEL (G08 PACKAGE) INPUT 2200 pF* 1 2200 pF 2 3 2200 pF 4 UPB586B UPB586G TEST CIRCUIT M VCC 2200 pF 8 2200 pF 7 6 5 OUTPUT DESCRIPTION The UPB586 series of devices are silicon bipolar prescalers which can be operated in divide-by-256 or divide-by-512 mode. They feature high frequency response and operat.

  UPB586G   UPB586G


Document
www.DataSheet4U.com 2.5 GHz DIVIDE- BY- 512/256 PRESCALER FEATURES • HIGH FREQUENCY OPERATION TO 2.5 GHz • WIDE BAND OPERATION • SINGLE SUPPLY VOLTAGE: VCC = 5 V ±10% • AVAILABLE IN TAPE AND REEL (G08 PACKAGE) INPUT 2200 pF* 1 2200 pF 2 3 2200 pF 4 UPB586B UPB586G TEST CIRCUIT M VCC 2200 pF 8 2200 pF 7 6 5 OUTPUT DESCRIPTION The UPB586 series of devices are silicon bipolar prescalers which can be operated in divide-by-256 or divide-by-512 mode. They feature high frequency response and operate from a single 5 volt supply. The series is available in two package styles: 8 lead ceramic flat pack (UPB586B) and an 8 pin plastic mini-flat package (UPB586G). Applications include frequency synthesis, division and scaling. *Not required if M is grounded. Note: Because of the high internal gain and gain compression of the UPB586, this device is prone to self-oscillation in the absence of an RF input signal. If the device will be used in an application where DC power will be applied in the absence of an RF input signal, this self-oscillation can be suppressed by any of the following means: * Add a shunt resistor from the RF input line to ground. The blocking capacitor should be between the resistor and the UPB586, but physical separation should be minimized. Typically a resistor value between 50 and 100 ohms will suppress the selfoscillation. * Apply a DC offset voltage of +3.0 volts to the INPUT pin. The voltage source should be isolated from the INPUT pin by a series 1000 ohm resistor. * Apply a DC offset voltage of +1.5 volts to the BYPASS pin. The voltage source should be isolated from the BYPASS pin by a series 1000 ohm resistor. All these approaches reduce the input sensitivity of the UPB586 (by as much as 3 dB for the example of a 50 ohm shunt resistor), but otherwise have no affect on the reliability or other electrical characteristics of this device. RECOMMENDED OPERATING CONDITIONS (TA = 25°C) SYMBOL VCC TOP PARAMETER Supply Voltage Operating Temperature UNITS V °C RATINGS 4.5 to 5.5 -20 to +75 ELECTRICAL CHARACTERISTICS1 (TA = -20 to +75°C, VCC = 5 V) PART NUMBER PACKAGE OUTLINE SYMBOLS ICC fIN PARAMETERS AND CONDITIONS Supply Current, TA = 25°C Frequency Response at PIN = -15 to -10 dBm PIN = -10 to -5 dBm PIN = -5 to +5 dBm Input Power at fIN = 0.5 to 1.3 GHz fIN = 1.3 to 2.3 GHz fIN = 2.3 to 2.5 GHz Power Output at fIN = 2 GHz, PIN = 0 dBm, TA = 25°C Thermal Resistance, Junction to Case (UPB586B) Thermal Resistance, Junction to Ambient (UPB586G)2 UNITS mA GHz GHz GHz dBm dBm dBm dBm °C/W °C/W MIN 19 0.5 0.5 1.3 -15 -15 -10 -11 -7 50 270 UPB586B, UPB586G BF08, G08 TYP 28 MAX 37 2.3 2.5 2.5 -5 +5 +5 PIN POUT RTH (J-C) RTH (J-A) Notes: 1. VCC = 5 V ± 10% (unless otherwise noted): ZS = ZO = 50 Ω. 2. Mounted on a 5 x 5 x 0.16 mm epoxy glass circuit board. California Eastern Laboratories UPB586B, UPB586G ABSOLUTE MAXIMUM RATINGS1 (TA = 25°C) SYMBOLS VCC VIN PIN PD PARAMETERS Supply Voltage Input Voltage Input Power Power Dissipation UPB586B UPB586G Operating Temperature UPB586B UPB586G Storage Temperature UPB586B UPB586G UNITS V V dBm W mW °C °C °C °C RATINGS -0.5 to 6.0 -0.5 to VCC + 0.5 +10 INPUT 2 1/256 BYPASS 3 7 OUTPUT 1/2 Buff. INTERNAL BLOCK DIAGRAM VCC 8 1.5 (TA = +125°C) 250 (TA = +85°C) -55 to +125 -40 to +85 TOP TSTG 4 1 M -55 to +200 -65 to +150 GND Note: 1. Operaton in excess of any one of these parameters may result in permanent damage. INPUT IMPEDANCE FOR UPB586G UPB586B INPUT AND OUTPUT S-PARAMETERS VCC = 5 V, ICC = 28 mA DIVIDE-BY-256 MODE Frequency (GHz) 0.20 0.40 0.60 0.80 1.00 1.20 1.40 1.60 1.80 2.00 2.20 2.40 2.60 2.80 3.00 MAG 0.768 0.752 0.734 0.715 0.698 0.686 0.663 0.629 0.591 0.547 0.502 0.456 0.413 0.378 0.355 S11 ANG -14 -29 -43 -57 -70 -84 -98 -112 -126 -139 -151 -162 -172 180 171 Frequency (GHz) 0.10 0.20 0.30 0.40 0.50 0.60 0.70 0.80 0.90 1.00 MAG 0.516 0.505 0.501 0.500 0.499 0.495 0.492 0.484 0.479 0.474 S22 ANG -9 -14 -20 -27 -33 -40 -46 -53 -59 -66 VCC = 5 V, IC = 28 mA, ZO = 50 Ω Frequency (GHz) 0.5 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.3 2.5 157.9 136.6 111.4 90.1 74.2 62.9 54.0 45.7 39.8 33.8 31.1 28.0 ZIN (Ω) -j99.9 -j79.9 -j61.3 -j43.4 -j29.7 -j20.2 -j13.7 -j8.6 -j4.3 -j0.1 +j1.6 +j4.5 DIVIDE-BY-512 MODE Frequency (GHz) 0.20 0.40 0.60 0.80 1.00 1.20 1.40 1.60 1.80 2.00 2.20 2.40 2.60 2.80 3.00 MAG 0.990 0.978 0.968 0.957 0.947 0.939 0.930 0.916 0.905 0.889 0.871 0.854 0.832 0.812 0.795 S11 ANG -11 -21 -32 -42 -52 -62 -72 -82 -92 -102 -112 -121 -130 -139 -144 Frequency (GHz) 0.10 0.20 0.30 0.40 0.50 0.60 0.70 0.80 0.90 1.00 MAG 0.495 0.487 0.482 0.482 0.482 0.477 0.476 0.468 0.471 0.458 S22 ANG -9 -14 -20 -26 -33 -39 -46 -53 -59 -65 UPB586B, UPB586G TYPICAL PERFORMANCE CURVES (TA = 25°C) CIRCUIT CURRENT vs. SUPPLY VOLTAGE 40 TA = 25˚C UPB586G INPUT POWER vs. FREQUENCY +40 VCC = 5.5 V VCC = 5.0 V VCC = 4.5 V TA = 25˚C Circuit Current, ICC (mA) +20 Input Power, PIN (dBm) 30 0 Operating Window -20 20 10 -40 0 0 2 4 6 -60 0.2 0.5 1.0 2.0 5..


UPB582C UPB586G UPB587G


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)