DatasheetsPDF.com

U2203B Dataheets PDF



Part Number U2203B
Manufacturers TEMIC Semiconductors
Logo TEMIC Semiconductors
Description RGB Video Amplifier System for Monitors
Datasheet U2203B DatasheetU2203B Datasheet (PDF)

U2203B RGB Video Amplifier System for Monitors Description The U2203B-A is a wideband video amplifier IC system especially designed for use in high-resolution RGB monitors. The IC includes three well matched video amplifiers, three gated differential amplifiers for blacklevel clamping and brightness control and the function for simultaneously contrast control. Separate adjustment of the maximum gain of each channel is also possible. Features D 3 channels, high bandwidth (90 MHz @ –3 dB) D Match.

  U2203B   U2203B



Document
U2203B RGB Video Amplifier System for Monitors Description The U2203B-A is a wideband video amplifier IC system especially designed for use in high-resolution RGB monitors. The IC includes three well matched video amplifiers, three gated differential amplifiers for blacklevel clamping and brightness control and the function for simultaneously contrast control. Separate adjustment of the maximum gain of each channel is also possible. Features D 3 channels, high bandwidth (90 MHz @ –3 dB) D Matched attenuators for contrast control D Black-level clamping for brightness control Vs1 1 SUPPLY REG. 1k D Independent gain control of each amplifier D ESD protection according to MIL-STD. 883 28 Vs1 CONTRAST CAP 2 27 R DRIVE CONTRAST CAP 3 RED 40 90 26 R CLAMP (–) R VIDEO IN 4 25 R VIDEO OUT R CLAMP CAP 5 24 R CLAMP (+) G VIDEO IN 6 GREEN 1k 40 23 Vs2 GROUND 7 90 22 G DRIVE G CLAMP CAP 8 9 21 G CLAMP (– ) B VIDEO IN B CLAMP CAP BLUE 1k 40 2.4V REF CONTRAST CONTROL 90 20 G VIDEO OUT 10 19 G CLAMP (+) Vin REF CONTRAST 11 12 18 B DRIVE 17 B CLAMP (–) Vs1 13 1.4V REF U2203B 95 10749 16 B VIDEO OUT CLAMP GATE 14 15 B CLAMP (+) Figure 1. Block diagram TELEFUNKEN Semiconductors Rev. A2, 27-Jan-97 1 (7) U2203B Pin Description VS1 Ccontr Ccontr Vin, R Cclamp, R Vin, G GND Cclamp, G Vin, B Cclamp, B VBias Vcontr VS1 VGate 1 2 3 4 5 6 7 8 9 10 11 12 13 14 96 12388 28 VS1 27 RR 26 VR– 25 Vout, R 24 VR+ 23 VS2 22 RG 21 VG– 20 Vout, G 19 18 17 16 15 VG+ RB VB– Vout, B VB+ Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Symbol VS1 Ccontr Ccontr Vin, R Cclamp, R Vin, G GND Cclamp, G Vin, G Cclamp, B VBias Vcontr VS1 VGate VB+ Vin, B VB– RB VG+ Vout, G VG– RG VS2 VR+ Vout, R VR– RR VS1 Function Supply voltage Contrast cap. Contrast cap. Video input (R) Clamp cap. (R) Video input (G) Ground Clamp cap. (G) Video input (B) Clamp cap. (B) Bias voltage (RGB-inputs) Contrast control Supply voltage Inverted clamp gate Clamp amplifier (B+) Video output (B) Clamp amplifier (B–) Drive resistor (B) Clamp amplifier (G+) Video output (G) Clamp amplifier (G–) Drive resistor (G) Supply voltage (outputs) Clamp amplifier (R+) Video output (R) Clamp amplifier (R–) Drive resistor (R) Supply voltage Figure 2. Pinning Absolute Maximum Ratings Parameters Supply voltage Pins 1, 13, 28 and 23 Input voltage at all other pins Video output current Pins 16, 20 and 25 Junction temperature Storage temperature range Symbol VS Vin IV Tj Tstg Value 13.5 0 toVS 28 125 –40 to 125 Unit V V mA °C °C Operating Range Parameters Ambient temperature range Supply voltage range Pins 1, 13, 23 and 28 Symbol Tamb VS2, VS1 Value 0 to 80 11.0 to 13.0 Unit °C V 2 (7) TELEFUNKEN Semiconductors Rev. A2, 27-Jan-97 U2203B Thermal Resistance Parameters Junction ambient (DIP28) Symbol RthJA Value 46 Unit K/W Electrical Characteristics Test conditions unless otherwise specified, reference point Pin 7, Tamb = 25°C, VS1 = VS2 = 12 V, V12 = 6 V (contrast); V14 = 0 V (inv. gating); V15 = V19 = V24 = 2 V (brightness) Parameters DC-values Supply current Input bias voltage Input bias current Switching voltage gating “on” Switching voltage gating “off” Switching current gating ”on” Switching current gating ”off” Charge current clamping capacitor Discharge current clamping capacitor Video outputs, VO Low level High level Output offset between two p amplifiers Test Conditions / Pins VS1 only, Pins 1, 13 and 28 Pin 11 Pins 4, 6 and 9 Pin 14 Pin 14 V14 = 0.8 V Pin 14 V14 = 2.0 V Pin 14 V5,8,10 = 0 V Pins 5, 8 and 10 V5,8,10 = 5 V Pins 5, 8 and 10 Pins 16, 20 and 25 V5,8,10 = 0 V V5,8,10 = VS V15, V19, V24 = 2 V ICL+ ICL– 0.8 –1.2 1.0 –1.0 1.2 –0.8 IG “H” 5 8 Symbol IS1 VinREF IinREF VG “L” VG “H” IG “L” –1 2.3 1 0.8 Min. Typ. 60 Max. 70 2.5 10 Unit mA V mA V V 5 1.3 1.5 –0.01 2.0 mA mA mA mA Video gain Maximum video gain Middle video gain Dynamic gain range Video gain match (any 2 outputs) Video bandwidth unpeaked (C = 0 pF) optimal peaking (C = 27 pF) Video cross talk 1) VO“L” VO“H” 8.0 DVO (2 V) V15, V19, V24 = 4 V DVO (4 V) V15 = V19 = V24 = 4 V (brightness); fIN = 1 MHz V12 = 12 V GVmax 16.0 V12 = 5 V GVmid GVD V12 = 12 V GVMmax GVMmid V12 = 5 V 1) GVM–30 V12 = 2.2 V V12 = 12 V (f–3dB) V12 = 12 V (f–3dB) fIN = 10 kHz fIN = 10 MHz BWV BWVP CT10kHz CT10MHz –50 0.8 8.6 1.0 ±50 ±50 V V mV mV 17.7 8.5 50 ±0.1 ±0.1 ±0.3 65 90 dB dB dB dB dB dB MHz MHz dB dB –47 Measured 30 dB below maximum gain TELEFUNKEN Semiconductors Rev. A2, 27-Jan-97 3 (7) U2203B VS (+12V) 100 mF 1 100 nF 2 100 nF 5 mF 3 4 75 W G Video in 75 W 10 kW 5 mF 100 nF 10 kW 5 mF 9 10 100 nF 11 12 10 kW Black level gate I/P 100 nF 14 15 10 kW 10 kW 100 nF 93 7632 28 27 51 W 100 W C 26 25 24 23 22 390 W R Clamp (–) To cascade driver (R) R Video in 5 mF 10 kW 100 nF 5 6 7 100 nF 51 W 100 W U2203B 8 21 20 C G Clamp (–) To cascade driver (G) B Video in 75 W 390 W 19 18 C 17 16 390 W 91 W G Clamp (–) To cascade driver (B) 13.


U211B3 U2203B U2270B


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)