DatasheetsPDF.com

X24165 Dataheets PDF



Part Number X24165
Manufacturers Xicor
Logo Xicor
Description Advanced 2-Wire Serial E2PROM with Block Lock Protection
Datasheet X24165 DatasheetX24165 Datasheet (PDF)

Preliminary Information 16K X24165 2048 x 8 Bit Advanced 2-Wire Serial E2PROM with Block LockTM Protection FEATURES DESCRIPTION The X24165 is a CMOS 16,384 bit serial E2PROM, internally organized 2048 x 8. The X24165 features a serial interface and software protocol allowing operation on a simple two wire bus. Three device select inputs (S0, S1, S2) allow up to eight devices to share a common two wire bus. A Write Protect Register at the highest address location, 7FFh, provides three new writ.

  X24165   X24165


Document
Preliminary Information 16K X24165 2048 x 8 Bit Advanced 2-Wire Serial E2PROM with Block LockTM Protection FEATURES DESCRIPTION The X24165 is a CMOS 16,384 bit serial E2PROM, internally organized 2048 x 8. The X24165 features a serial interface and software protocol allowing operation on a simple two wire bus. Three device select inputs (S0, S1, S2) allow up to eight devices to share a common two wire bus. A Write Protect Register at the highest address location, 7FFh, provides three new write protection features: Software Write Protect, Block Write Protect, and Hardware Write Protect. The Software Write Protect feature prevents any nonvolatile writes to the X24165 until the WEL bit in the write protect register is set. The Block Write Protection feature allows the user to individually write protect four blocks of the array by programming two bits in the write protect register. The Programmable Hardware Write Protect feature allows the user to install the X24165 with WP tied to VCC, program the entire memory array in place, and then enable the hardware write protection by programming a WPEN bit in the write protect register. After this, selected blocks of the array, including the write protect register itself, are permanently write protected. Xicor E2PROMs are designed and tested for applications requiring extended endurance. Inherent data retention is greater than 100 years. • • • • • • • • • • • 2.7V to 5.5V Power Supply Low Power CMOS —Active Read Current Less Than 1mA —Active Write Current Less Than 3mA —Standby Current Less Than 1µA Internally Organized 2048 x 8 New Programmable Block Lock Protection —Software Write Protection —Programmable Hardware Write Protect Block Lock (0, 1/4, 1/2, or all of the E2PROM array) 2 Wire Serial Interface Bidirectional Data Transfer Protocol 32 Byte Page Write Mode —Minimizes Total Write Time Per Byte Self Timed Write Cycle —Typical Write Cycle Time of 5ms High Reliability —Endurance: 100,000 Cycles —Data Retention: 100 Years Available Packages —8-Lead PDIP —8-Lead SOIC (JEDEC) —14-Lead TSSOP FUNCTIONAL DIAGRAM WP START CYCLE VCC VSS SDA START STOP LOGIC CONTROL LOGIC SLAVE ADDRESS REGISTER +COMPARATOR XDEC E2PROM 64 X 256 WRITE PROTECT REGISTER AND LOGIC H.V. GENERATION TIMING & CONTROL SCL S2 S1 S0 LOAD INC WORD ADDRESS COUNTER R/W YDEC 8 CK PIN DOUT ACK DATA REGISTER DOUT 6551 ILL F01.1 ©Xicor, 1995, 1996 Patents Pending 6551-2.5 5/13/96 T1/C10/D0 NS 1 Characteristics subject to change without notice X24165 PIN DESCRIPTIONS Serial Clock (SCL) The SCL input is used to clock all data into and out of the device. Serial Data (SDA) SDA is a bidirectional pin used to transfer data into and out of the device. It is an open drain output and may be wire-ORed with any number of open drain or open collector outputs. An open drain output requires the use of a pull-up resistor. For selecting typical values, refer to the PullUp Resistor selection graph at the end of this data sheet. Device Select (S0, S1, S2) The device select inputs (S0, S1, S2) are used to set the first three bits of the 8-bit slave address. This allows up to eight X24165’s to share a common bus. These inputs can be static or actively driven. If used statically they must be tied to VSS or VCC as appropriate. If actively driven, they must be driven with CMOS levels (driven to VCC or VSS). Write Protect (WP) The write protect input controls the hardware write protect feature. When held LOW, hardware write protection is disabled and the X24165 can be written normally. When this input is held HIGH, and the WPEN bit in the write protect register is set HIGH, write protection is enabled, and nonvolatile writes are disabled to the selected blocks as well as the write protect register itself. PIN NAMES Symbol S0, S1, S2 SDA SCL WP VSS VCC NC PIN CONFIGURATIONS 8-LEAD DIP & SOIC S0 S1 S2 VSS 1 2 3 4 X24165 8 7 6 5 VCC WP SCL SDA 14-LEAD TSSOP S0 S1 NC NC NC S2 VSS 1 2 3 4 5 6 7 14 13 12 X24165 11 10 9 8 VCC WP NC NC NC SCL SDA 6551 ILL F02.5 Description Device Select Inputs Serial Data Serial Clock Write Protect Ground Supply Voltage No Connect 6551 FRM T01.2 2 X24165 DEVICE OPERATION The X24165 supports a bidirectional bus oriented protocol. The protocol defines any device that sends data onto the bus as a transmitter, and the receiving device as the receiver. The device controlling the transfer is a master and the device being controlled is the slave. The master will always initiate data transfers, and provide the clock for both transmit and receive operations. Therefore, the X24165 will be considered a slave in all applications. Clock and Data Conventions Data states on the SDA line can change only during SCL LOW. SDA state changes during SCL HIGH are reserved for indicating start and stop conditions. Refer to Figures 1 and 2. Start Condition All commands are preceded by the start condition, which is a HIGH to LOW transition of SDA when SCL is HIGH. The X24165 continuously monitors the SDA and SC.


X24164 X24165 X24320


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)