Document
Data Sheet No. PD60107 revY
IR2133/IR2135(J&S) & (PbF) IR2233/IR2235(J&S) & (PbF)
3-PHASE BRIDGE DRIVER
Features
• Floating channel designed for bootstrap operation Fully operational to +600V or+1200V Tolerant to negative transient voltage dV/dt immune
• Gate drive supply range from 10V/12V to 20V DC and up to 25V for transient
• Undervoltage lockout for all channels • Over-current shut down turns off all six drivers • Independent 3 half-bridge drivers • Matched propagation delay for all channels • 2.5V logic compatible • Outputs out of phase with inputs • All parts are also available LEAD-FREE
Product Summary
VOFFSET IO+/-
VOUT ton/off (typ.) Deadtime (typ.)
600V or 1200V max. 200 mA / 420 mA 10 - 20V or 12 - 20V
750/700 ns 250 ns
Packages
Description
The IR2133IR2135/IR2233IR2355 (J&S) are high voltage, high speed
power MOSFET and IGBT driver with three independent high side and
low side referenced output channels for 3-phase applications. Proprietary HVIC technology enables ruggedized monolithic construction. Logic inputs are compatible with CMOS or LSTTL outputs, down to
28-Lead SOIC
28-Lead PDIP
2.5V logic. An independent operational amplifier provides an analog
feedback of bridge current via an external current sense resistor. A
44-Lead PLCC w/o 12 leads
current trip function which terminates all six outputs can also be de-
rived from this resistor. A shutdown function is available to terminate all six outputs. An open drain FAULT signal is provided to
indicate that an over-current or undervoltage shutdown has occurred. Fault conditions are cleared with the FLT-CLR lead. The
output drivers feature a high pulse current buffer stage designed for minimum driver cross-conduction. Propagation delays are
matched to simplify use in high frequency applications. The floating channels can be used to drive N-channel power MOSFETs or
IGBTs in the high side configuration which operates up to 600 volts or 1200 volts.
Typical Connection
up to 600V or 1200V
(Refer to Lead Assignments for correct pin configuration). This/These diagram(s) show electrical connections only. Please refer to our Application Notes and DesignTips for proper circuit board layout.
www.irf.com
1
IR2133/IR2135/IR2233/IR2235(J&S) & (PbF)
Absolute Maximum Ratings
Absolute Maximum Ratings indicate sustained limits beyond which damage to the device may occur. All voltage parameters are absolute voltages referenced to COM. The Thermal Resistance and Power Dissipation ratings are measured under board mounted and still air conditions.
Symbol Definition
Min.
Max.
Units
VB1,2,3
VS1,2,3 VHO1,2,3 VCC VSS VLO1,2,3 VIN
High side floating supply voltage (IR2133/IR2135) (IR2233/IR2235)
High side floating supply offset voltage High side floating output voltage Fixed supply voltage Logic ground Low side output voltage Logic input voltage (HIN, LIN, ITRIP, SD & FLT-CLR)
-0.3 -0.3 VB1,2,3 - 25 VS1,2,3 - 0.3 -0.3 VCC - 25 -0.3 VSS - 0.3
VIN,AMP Op amp input voltage (CA+ & CA-)
VOUT,AMP Op amp output voltage (CAO)
VFLT
FAULT output voltage
dVS/dt Allowable offset supply voltage transient
PD
Package power dissipation @ TA ≤ 25ºC (28 Lead PDIP)
(28 Lead SOIC)
(44 lead PLCC)
RthJA Thermal resistance, junction to ambient (28 Lead PDIP)
(28 Lead SOIC)
(44 lead PLCC)
TJ
Junction temperature
TS
Storage temperature
TL
Lead temperature (soldering, 10 seconds
VSS - 0.3 VSS - 0.3 VSS - 0.3
— — — — — — — — -55 —
625 1225 VB1,2,3 + 0.3 VB1,2,3 + 0.3
25 VCC + 0.3 VCC + 0.3 (VSS + 15) or (VCC + 0.3) whichever is lower VCC + 0.3 VCC + 0.3 VCC + 0.3
50 1.5 1.6 2.0 83 78 63 125 150 300
V
V/ns W
ºC/W ºC
Recommended Operating Conditions
The input/output logic timing diagram is shown in figure 1. For proper operation the device should be used within the
recommended conditions. All voltage parameters are absolute voltages referenced to COM. The VS offset rating is tested with all supplies biased at 15V differential.
Symbol Parameter Definition
Min.
Max.
Units
VB1,2,3
High side floating supply voltage
VS1,2,3 + 10/12 VS1,2,3 + 20
VS1,2,3
High side floating supply offset voltage (IR2133/IR2135)
Note 1
600
(IR2233/IR2235) Note 1
1200
VHO1,2,3 High side floating output voltage
VS1,2,3
VB1,2,3
VCC
Fixed supply voltage
10 or 12
20
VSS VLO1,2,3
Low side driver return Low side output voltage
-5
5
V
0
VCC
VIN
Logic input voltage (HIN, LIN, ITRIP, SD & FLT-CLR)
VSS
VSS + 5
VIN,AMP Op amp input voltage (CA+ & CA-)
VSS
VSS + 5
VOUT,AMP Op amp output voltage (CAO)
VFLT
FAULT output voltage
VSS
VSS + 5
VSS
VCC
Note 1: Logic operational for VS of COM - 4V to COM + 600V/1200V. Logic state held for VS of COM -4V to COM -VBS. (Please refer to the Design Tip DT97-3 for more details). Note 2: All input pins, op amp input and output pins are internally clamped with a 5.2V zener diode.
2
www.irf.com
IR2133/IR2135/IR2233/IR2235(J&S) & (PbF)
Dynamic Electrical Characte.