DatasheetsPDF.com

53012 Dataheets PDF



Part Number 53012
Manufacturers Micropac Industries
Logo Micropac Industries
Description SPST SOLID-STATE RELAY
Datasheet 53012 Datasheet53012 Datasheet (PDF)

53012 SPST SOLID-STATE RELAY Mii HYBRID MICROELECTRONICS PRODUCTS DIVISION Features: • • • • • • • • Replacement for M90FS-2 SPST, Normally Open Integral Short Circuit Protection Power FET Output Low On-state Resistance Full Military Temperature Operation: -55ºC to +125ºC Military Environmental Screening Available Improved Thermal Characteristics Built in accordance with 85006-001 Applications: • • • • • Low Level Power Control Current Loop Switches Isolated Line Driver Selection Servo and Sy.

  53012   53012


Document
53012 SPST SOLID-STATE RELAY Mii HYBRID MICROELECTRONICS PRODUCTS DIVISION Features: • • • • • • • • Replacement for M90FS-2 SPST, Normally Open Integral Short Circuit Protection Power FET Output Low On-state Resistance Full Military Temperature Operation: -55ºC to +125ºC Military Environmental Screening Available Improved Thermal Characteristics Built in accordance with 85006-001 Applications: • • • • • Low Level Power Control Current Loop Switches Isolated Line Driver Selection Servo and Synchro Resolver Control Military/Aerospace General Purpose Switching DESCRIPTION The 53012 is a military SPST solid-state relay. This light-weight device is resistant to damage from shock and vibration, and is immune to contact-related problems (contamination, arcing) associated with mechanical equivalents. Optical coupling between the input and output stages provides effective isolation up to 1000 volts AC RMS. Power FET outputs eliminate bipolar offset, and minimize output voltage drop. The control logic is TTL compatible, and will accommodate bias supplies between 3.8 and 32 VDC. Integral short-circuit protection is provided in the 53012. This unit senses excessive current flow while under load or while switching, and respond by opening the output. The output will remain blocked indefinitely until the short is removed, and the unit reset. This feature prevents damage to the unit, and also averts further system failures that may be caused by the shortcircuit. Resetting the unit can be accomplished by cycling the input control. This solid-state relay is ideal for use in military systems, or wherever high reliability, low power actuation, and light weight are design considerations. Applications include general purpose signal switching and electronic load control. ABSOLUTE MAXIMUM RATINGS Isolation Voltage: 53012 ....................................................................................................................................... 1000 VAC RMS Operating Temperature ............................................................................................................................. -55ºC to +125ºC Case Storage Temperature ......................................................................................................................................... -55ºC to +125ºC Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement. Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible. MICROPAC INDUSTRIES, INC. HYBRID MICROELECTRONICS PRODUCTS DIVISION • 905 E. Walnut St, Garland, TX 75040 • (972) 272-3571 • Fax (972) 494-2281 www.micropac.com E-MAIL: [email protected] 03/15/01 53012 SPST SOLID-STATE RELAY ELECTRICAL CHARACTERISTICS* TA = +25° C PARAMETER Input Current Control Voltage Range Turn-Off Voltage Turn-On Voltage Continuous Operating Output Voltage Load Current On Resistance Output Capacitance Thermal Resistance ΘJA Thermal Resistance ΘJC Rise Time, tr Fall Time, tr On Delay, tdON Off Delay, tdOFF Surge Voltage Leakage Current Dielectric Strength Isolation Resistance Current Surge Overload Trip Current NOTES: 1. 2. 3. 4. Limiting resistor may be required for VC > 6V. See Table 1 Input transitions should be < 1 ms Maximum input frequency: 50Hz (Normal load). For shorted load, use: fSC = 50 – (1.17 X VOUT) tON = tr + tdON , tOFF = tf + tdOFF CONDITIONS See Table 1 – Bias Resistance MIN 3.8 3.8 TYP 13 MAX 16 32 1.5 60 UNIT MA VDC VDC VDC VDC Amps Ohms pF ºC/W ºC/W µs µs µs µs Volts µA VAC RMS Ohms Amps DC Amps DC 25ºC 0.2 25V, 1MHz 100 25 10% - 90% Load Voltage 90% - 10% Load Voltage Min Turn On Volts To 10% Load V Max Turn Off Volts To 90% Load V 5 Second Maximum Max Cont. Operating Output V I-0, 60 Hz Sine Wave Input to Case, 500 V 100 ms 40 ms Pulse 1.0 0.3 400 1000 100 800 500 80 10 1000 10 2 9 8.5 Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement. Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible. MICROPAC INDUSTRIES, INC. HYBRID MICROELECTRONICS PRODUCTS DIVISION • 905 E. Walnut St, Garland, TX 75040 • (972) 272-3571 • Fax (972) 494-2281 www.micropac.com E-MAIL: [email protected] 03/15/01 53012 SPST SOLID STATE RELAY APPLICATION INFORMATION +VC=5V R St NC + D C S u p p ly T T L (O .C .) 5 4 3 7 1 O u tp u t G ro u n d I 16 A *Limiting Resistor (RS) May Be Required. See Table 1. TABLE 1 LIMITING RESISTANCE (RS) VALUES (Without Heat Sink) 3.8-6 VC (VDC) RS (Ω) Rating 6 – 10 300 1/4 10 – 14 620 1/4 14 – 18 910 1/2 22 – 26 1500 1/2 26 - 32 2000 1 Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement. Micropac reserves the right to make changes at any time in order to impro.


5275 53012 53024


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)