DatasheetsPDF.com

M-985-01S Dataheets PDF



Part Number M-985-01S
Manufacturers Clare Inc.
Logo Clare  Inc.
Description Precise Call Progress and Special Information Tone Generator
Datasheet M-985-01S DatasheetM-985-01S Datasheet (PDF)

M-985-01 Precise Call Progress and Special Information Tone Generator Features • • • • • • • • • • Precise detection of call progress tones Linear (analog) input Digital (CMOS compatible), tri-state outputs 22-pin DIP and 20-pin SOIC Single supply 3 to 5 volt (low power CMOS) Inexpensive 3.58 MHz crystal time base Wide dynamic range (30 dB) Lower power consumption (power-down mode) 425 Hz detection Special Information Tone (SIT) Detection Description The M-985-01 is an integrated circuit precise.

  M-985-01S   M-985-01S


Document
M-985-01 Precise Call Progress and Special Information Tone Generator Features • • • • • • • • • • Precise detection of call progress tones Linear (analog) input Digital (CMOS compatible), tri-state outputs 22-pin DIP and 20-pin SOIC Single supply 3 to 5 volt (low power CMOS) Inexpensive 3.58 MHz crystal time base Wide dynamic range (30 dB) Lower power consumption (power-down mode) 425 Hz detection Special Information Tone (SIT) Detection Description The M-985-01 is an integrated circuit precise tone detector for call progress and special information tones (SIT), as defined by CCITT. The use of integrated circuit techniques allows the M-985-01 to pack the eight filters for call progress detection into a single 22-pin DIP or a 20-pin SOIC. A 3.58 MHz crystal-controlled time base guarantees accuracy and repeatability. The M-985-01 combines the call progress detection of the M-982-02 and the SIT detection of the M-984-02. It has an operating voltage range down to 3V. It has low power consumption under normal operating conditions. A power down (PD) feature is provided to further reduce power consumption when inactive. Ordering Information Part # M-985-01P M-985-01S M-985-01T Applications • Automatic dialers • Dialing modems • Traffic measurement equipment • Test equipment • Service evaluation • Billing systems Description 22-pin plastic DIP 20-pin plastic SOIC 20-pin plastic SOIC,Tape and Reel Pin Diagram Block Diagram DS-M985-01-R1 www.clare.com 1 M-985-01 Absolute Maximum Ratings Storage Temperature Operating Ambient Temperature VDD Input Voltage on SIGIN Input Voltages (except SIGIN) Lead Soldering Temperature Note: Exceeding these ratings may permanently damage the M-985-01. -40 to 150°C -40 to 85°C 7V VSS - 6.5 to VDD + 0.3V VSS - 0.3 to VDD + 0.3 V 260° C for 5 seconds Absolute Maximum Ratings are stress ratings. Stresses in excess of these ratings can cause permanent damage to the device. Functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this data sheet is not implied. Exposure of the device to the absolute maximum ratings for an extended period may degrade the device and effect its reliability. Specifications Parameter Operating Conditions Power VREF Signal Detection, all tones except SIT tones. VDD Power supply noise Current drain (IDD) VREF Impedance Frequency range Level: VDD = 5.0v Level: VDD = 3.0V Duration (tDD) Signal drop out bridging time (tBB) Level skew between adjacent inband signals High level to low level signal for detection of both (tIL) Time to output (tDO) Time from OUT n to STROBE (tDS) Signal Detection, Frequency Range 940, 1400, 1800 Level: VDD = 5.0V Hz Level: VDD = 3.0V Duration Signal drop out bridging time (tBB) Signal to noise ratio Signal Rejection, Frequency range all tones except Level: VDD = 5.0V SIT tones. Level: VDD = 3.0V Interval duration (tID) Time to end of output (tIO) Conditions 0.1 - 5 kHz in-band signal XRANGE = open XRANGE = VSS XRANGE = open XRANGE = VSS for detection of both Min 2.7 48% of VDD 3.25 -1 -30 (24.5 mV) -40 (7.8 mV) -33 (17.4 mV) -43 (5.5 mV) 200 Max 5.5 20 15 52% of VDD 8.25 +1 0 (775 mV) -10 (245 mV) -3 (549 mV) -13 (173.5 mV) 20 6 200 240 10 0 (775 mV) -10 (245 mv) -3 (549 mV) -13 (173.5 mV) 15 +6 -50 (2.5 mV) -60 (0.8 mv) -53 (1.7 mV) -65 (.55 mV) 200 Units V mV p-p mA V kΩ % of fo dBm dBm dBm dBm ms ms dB s ms ms µs dBm dBm dBm dBm ms ms dB % of f0 dBm dBm dBm dBm ms ms Notes 1 High = 0 dBm (775 mV) 1 Low = -30 dBm (24.5 mV) SIGIN ≥ -24 dBm SIGIN < -24 dBm XRANGE = open -30 (24.5 mV) XRANGE = VSS -40 (7.8 mV) XRANGE = open -33 (17.4 mV) XRANGE = VSS -43 (5.5 mV) 50 16 -6 XRANGE = open XRANGE = VSS XRANGE = open XRANGE = VSS 160 - 2 - 1 - 2 www.clare.com Rev. 1 M-985-01 Specifications (Continued) Parameter Signal Rejection, Frequency Range 950, 1400, 1800 Level: VDD = 5.0V Hz Level: VDD = 3.0V Duration OUT n, STROBE pins OUT n pins EN, OE, XRANGE, MODE, PD pins Pull-up and Pull-down currents Conditions XRANGE = open XRANGE = VSS XRANGE= open XRANGE= VSS ISINK = -1mA ISOURCE = 1mA VO=VDD, VSS VDD = 5V VDD = 2.7V VDD = 5V VDD = 2.7V VDD = 5V VDD = 2.7V PD = VDD f=500 Hz XOUT open XOUT open XOUT open PD hi to lo CL = 20 pF, ISINK = -1mA CL = 20 pF, ISOURCE = 1mA CL = 20 pF CL = 50 pF, RL = 100 kΩ Min 50 VDD -0.5 VDD - 2.0 VDD - 0.5 12.5 4 2 12.5 12.5 4 12.5 -6.5 80 VDD-0.2 40 20 VDD - 0.2 40 Max -40 (7.8 mV) -50 (2.5 mV) -43 (5.5 mV) -53 (1.7 mV) ms 0.5 1 0.5 50 20 6 100 25 10 50 VDD 28 0.2 60 10 30 0.2 60 250 250 Units dBm dBm dBm dBm V V µA V V V µA µA µA µA µA µA µA V kΩ kHz V V % pF MΩ ms V V % ns ns Notes 2 - Outputs Inputs VOL VOH IOZ VIL VIH MODE = VSS /XRANGE = VSS MODE2 = VDD PD pin SIGIN pin Clock PD = VDD Pull-down current Voltage range Input impedance Input spectrum External clock VIL connected to XIN VIH pin Duty cycle XIN, XOUT with Capacitance crystal osc. active Internal resistance Power up (tPU) X358 pin VOL VOH Tri-state Operation Dut.


M-985-01P M-985-01S M-985-01T


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)