DatasheetsPDF.com

MIM-0KM1AKL Dataheets PDF



Part Number MIM-0KM1AKL
Manufacturers Unity Opto Technology
Logo Unity Opto Technology
Description INFRARED RECEIVER MODULE
Datasheet MIM-0KM1AKL DatasheetMIM-0KM1AKL Datasheet (PDF)

INFRARED RECEIVER MODULE Description The MIM-0KM1AKL is miniaturized infrared receivers for remote control and other appplications requiring improved ambient light rejection. The separate PIN diode and preamplifier IC are assembled on a single leadframe. The epoxy package contains a special IR filter. This module has excellent performance even in disturbed ambient light applications and provides protection against uncontrolled output pulses. MIM-0KM1AKL Features Photo detector and preamplifier.

  MIM-0KM1AKL   MIM-0KM1AKL


Document
INFRARED RECEIVER MODULE Description The MIM-0KM1AKL is miniaturized infrared receivers for remote control and other appplications requiring improved ambient light rejection. The separate PIN diode and preamplifier IC are assembled on a single leadframe. The epoxy package contains a special IR filter. This module has excellent performance even in disturbed ambient light applications and provides protection against uncontrolled output pulses. MIM-0KM1AKL Features Photo detector and preamplifier in one package Internal filter for PCM frequency High immunity against ambient light Improved shielding against electric field disturbance 2.4-Volt supply voltage; low power consumption TTL and CMOS compatibility MIM-0KM1xKL Series Models MIM-0KM1AKL 37.9KHz MIM-0KM1BKL 32.7KHz MIM-0KM1CKL 40.0KHz MIM-0KM1DKL 36.7KHz MIM-0KM1FKL 56.7KHz Unit : mm BLOCK DIAGRAM VS TRAP BPF TRIMMING Output ABLC fo GND Unity Opto Technology Co., Ltd. 1/12/01 MIM-0KM1AKL Absolute Maximum Ratings Item Supply voltage Operating temperature Storage temperature Soldering temperature Symbol VCC Topr Tstg Tsd Ratings 3.0 ~ 5.8 -10 ~ + 60 -20 ~ + 75 260 Unit V ℃ ℃ ℃ Maximum 5 seconds @ Ta=25℃ Remark Electro-optical characteristics (Vcc=2.4V) Parameter Current consumption Response wavelength Tuning frequency Output form H level output voltage L level output voltage H level output pulse width L level output pulse width Distance between emitter & detector Half angle V0h V0l Twh Twl L1(Vcc=3V) L2(Vcc=2.4V) △Θ 400 400 10.0 7.0 ±45 Symbol Icc λp f0 940 37.9 Min. Typ. Max. 5.0 Unit mA nm KHZ (Ta=25°C , Vcc=2.4V) Remarks Under no signal - - - - - active low output - - - - 2.2 0.5 800 800 V V μs μs m m deg Horizonal direction Note 1 Test Method A. Standard Transmitter 25cm ON/OFF pulse width satisfied from 25 cm to detection limit PD3516 600µs Transmitter Duty 50% +2.4V 10kΩ 10µF Vout GND Oscilloscope 600µs 600µs Fig 1. Burst Wave Fig 2. Standard Transmitter Measurement circuit B. Detection Length Test θ θ D.U.T L θ: indicates horizontal and vertical directions Transmitter output Vout Unity Opto Technology Co., Ltd. 10k 1/12/01 MIM-0KM1AKL C. Pulse Width Test Transmitter output 600µs 600µs DUT output pulse Twl Twh V0h V0l Application Circuit Vcc **) MIM-0KM1xKL MIE-544A2 3 102P C Decoder 1 2 GND *) only necessary to supress power supply disturbances. **) tolerated supply voltage range : 2.4V < Vcc < 5.8V CHARACTERISTIC CURVES (TA=25℃) 2.8 2.7 2.6 2.4 2.2 2.0 400 2 3 6 4 5 Supply Voltage Vcc (V) 7 8 0.1 1 10 Input Level (mVp-p) 100 1000 Output Pulse Width tPW(µs) Supply Current Icc (mA) 900 800 700 600 500 Input Level VIN (mVP-P) Burst length * 600µs, cycle = 1.2ms tpw: Average value of output from start of signal input to 60th pulse SUPPLY VOLTAGE vs. SUPPLY CURRENT INPUT LEVEL vs.OUTPUT PULSE WIDTH NOTE 1. Distance between emitter & detector specifies maximum distance that output wave form satisfies the standard under the conditions below against the standerd transmitter. (1)Measuring place ………Indoor without extreme reflection of light. (2)Ambient light source… Detecting surface illumination shall be 200±50Lux under ordinary hite fluorescense lamp of no high frequency lighting. (3)Standard transmitter … Burst wave indicated in Fig 1. of standard transmitter shall be arranged to 50mVp-p under the measuring circuit specified in Fig 2. Unity Opto Technology Co., Ltd. 1/12/01 MIM-0KM1AKL Reliability Test item High temparature High temp. & high humi. Low temparature Heat cycle Dropping Ta=+60℃ Vcc=5.0 V Ta=+40℃ 90%RH Vcc=5.0V Ta= -10℃ Vcc=5.0V -20℃(0.5H) ~ +75℃(0.5H) 20cycle Test devices shall be dropped 3 times naturally onto hard wooden board from a 75cm height position. NOTE 2. (electro-optical charactistics) shall be satisfied sfter leaving 2 hours in the normal temperature . NOTE 3. (electro-optical charactistics) shall be satisfied and no conoid deforms and destructions of appearance .(excepting deforms of terminals) Test condition t=240H t=240H t=240H Standard Note 2. Note 2. Note 2. Note 2. Note 3. Inspection standard 1.Among electrical characteristics , total number shall be inspected on items blow. 1-1 front distance between emitter & detector 1-2 Current consumption 1-3 H level output voltage 1-4 L level output voltage 2.Items except above mentioned are not inspected particularly , but shall fully satisfy CAUTION ( When use and storage of this device ) 1.Store and use where there is no force causing transformation or change in quality . 2.Store and use where there is no corrosive gas or sea(salt) breeze . 3.Store and use where there is no extreme humidity . 4.Solder the lead-pin within the condition of ratings. After soldering do not add extra force . 5.Do not wash this device . Wipe the stains of diode side with a soft cloth. You can use the solvent , ethylalcohol or methylalcohol or isupropylene only . 6.To prevent static electricity damage to the Pre-AMP make sure that the human body , the soldering .


MIM-0KM1AKF MIM-0KM1AKL MIM-0KM2AKF


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)