Document
H
Subminiature LED Lamps Technical Data
HLMP-PXXX Series HLMP-QXXX Series HLMP-6XXX Series HLMP-70XX Series
Features
• Subminiature Flat Top Package Ideal for Backlighting and Light Piping Applications • Subminiature Dome Package Diffused Dome for Wide Viewing Angle Nondiffused Dome for High Brightness • Arrays • TTL and LSTTL Compatible 5 Volt Resistor Lamps • Available in Six Colors • Ideal for Space Limited Applications • Axial Leads • Available with Lead Configurations for Surface Mount and Through Hole PC Board Mounting
Dome Packages The HLMP-6XXX Series dome lamps for use as indicators use a tinted, diffused lens to provide a wide viewing angle with a high on-off contrast ratio. High brightness lamps use an untinted, nondiffused lens to provide a high luminous intensity within a narrow radiation pattern. Arrays The HLMP-66XX Series subminiature lamp arrays are available in lengths of 3 to 8 elements per array. The luminous intensity is matched within an array to assure a 2.1 to 1.0 ratio. Resistor Lamps The HLMP-6XXX Series 5 volt subminiature lamps with built in current limiting resistors are for use in applications where space is at a premium. Lead Configurations All of these devices are made by encapsulating LED chips on axial lead frames to form molded epoxy subminiature lamp packages. A variety of package configuration options is available. These include special
surface mount lead configurations, gull wing, yoke lead or Zbend. Right angle lead bends at 2.54 mm (0.100 inch) and 5.08 mm (0.200 inch) center spacing are available for through hole mounting. For more information refer to Standard SMT and Through Hole Lead Bend Options for Subminiature LED Lamps data sheet.
Description
Flat Top Package The HLMP-PXXX Series flat top lamps use an untinted, nondiffused, truncated lens to provide a wide radiation pattern that is necessary for use in backlighting applications. The flat top lamps are also ideal for use as emitters in light pipe applications.
1-174
5964-9350E
Device Selection Guide Part Number: HLMP-XXXX
Standard Red DH AS High High AlGaAs Efficiency Perf. Emerald Red Red Orange Yellow Green Green P105 P102 6000/6001 Q101 Q105 Q150 Q155 6600 6620 6203 6204 6205 6206 6208 6653 6654 6655 6656 6658 6700 6720 6753 6754 6755 6756 6758 6800 6820 6853 6854 6855 6856 6858 P205 P202 6300 6305 7000 P405 P402 Q400 P305 P302 6400 6405 7019 P505 P502 6500 6505 7040 Q600 P605 Device Outline Drawing A B
Device Description[1] Untinted, Nondiffused, Flat Top Untinted, Diffused, Flat Top Tinted, Diffused Untinted, Nondiffused, High Brightness Tinted, Diffused, Low Current Nondiffused, Low Current Tinted, Diffused, Resistor, 5 V, 10 mA Diffused, Resistor, 5 V, 4 mA 3 Element Matched 4 Element Array, Tinted, 5 Element Diffused 6 Element 8 Element
B
C
Package Dimensions
(A) Flat Top Lamps
NOTES: 1. ALL DIMENSIONS ARE IN MILLIMETERS (INCHES). 2. PROTRUDING SUPPORT TAB IS CONNECTED TO CATHODE LEAD.
*Refer to Figure 1 for design concerns.
1-175
Package Dimensions (cont.)
(B) Diffused and Nondiffused
NOTES: 1. ALL DIMENSIONS ARE IN MILLIMETERS (INCHES). 2. PROTRUDING SUPPORT TAB IS CONNECTED TO CATHODE LEAD.
*Refer to Figure 1 for design concerns.
(C) Arrays
NOTES: 1. ALL DIMENSIONS ARE IN MILLIMETERS (INCHES). 2. PROTRUDING SUPPORT TAB IS CONNECTED TO CATHODE LEAD.
Figure 1. Proper Right Angle Mounting to a PC Board to Prevent Protruding Cathode Tab from Shorting to Anode Connection.
1-176
Absolute Maximum Ratings at TA = 25°C
Parameter DC Forward Current[1] Peak Forward Current[2] DC Forward Voltage (Resistor Lamps Only) Reverse Voltage (IR = 100 µA) Transient Forward Current (10 µs Pulse)
[3]
Standard Red 50 1000
DH AS AlGaAs Red 30 300
High Eff. Red 30 90 6
Orange 30 90
Yellow 20 60 6
High Perf. Emerald Green Green Units 30 90 6 5 500 -40 to +100 -20 to +85 °C 30 90 6 5 500 -20 to +100 mA mA V V mA
5 2000 -55 to +100
5 500 -40 to +100
5 500
5 500 -55 to +100 -40 to +85
5 500
Operating Temperature Range: Non-Resistor Lamps Resistor Lamps Storage Temperature Range For Thru Hole Devices Wave Soldering Temperature [1.6 mm (0.063 in.) from body] For Surface Mount Devices: Convective IR Vapor Phase
°C
-55 to +100 260°C for 5 Seconds
235°C for 90 Seconds 215°C for 3 Minutes
Notes: 1. See Figure 5 for current derating vs. ambient temperature. Derating is not applicable to resistor lamps. 2. Refer to Figure 6 showing Max. Tolerable Peak Current vs. Pulse Duration to establish pulsed operating conditions. 3. The transient peak current is the maximum non-recurring peak current the device can withstand without failure. Do not operate these lamps at this high current.
1-177
Electrical/Optical Characteristics, TA = 25°C
Standard Red Device HLMP6000 6001 6203 to 6208 Forward Voltage All P005 All Others Peak Wavelength Dominant Wavelength[3] Spectral Line Half Width All Speed of Response Capacitance Thermal Resistance Luminous Efficacy[4] λPEAK λd ∆λ1/2 τs C RθJ-PIN ηv Reverse Breakdown Vol.