DatasheetsPDF.com

TSOP2433 Dataheets PDF



Part Number TSOP2433
Manufacturers Vishay
Logo Vishay
Description IR Receiver
Datasheet TSOP2433 DatasheetTSOP2433 Datasheet (PDF)

Datasheet Values Refer to PCN-OPT-1224-2022 www.vishay.com TSOP22.., TSOP24.., TSOP48.., TSOP44.. Vishay Semiconductors IR Receiver Modules for Remote Control Systems 23196 LINKS TO ADDITIONAL RESOURCES Product Page Marking Packages Holders Bends and Cuts DESCRIPTION This IR receiver series is optimized for long burst remote control systems in different environments. The customer can chose between different IC settings (AGC variants), to find the optimum solution for his application. .

  TSOP2433   TSOP2433


Document
Datasheet Values Refer to PCN-OPT-1224-2022 www.vishay.com TSOP22.., TSOP24.., TSOP48.., TSOP44.. Vishay Semiconductors IR Receiver Modules for Remote Control Systems 23196 LINKS TO ADDITIONAL RESOURCES Product Page Marking Packages Holders Bends and Cuts DESCRIPTION This IR receiver series is optimized for long burst remote control systems in different environments. The customer can chose between different IC settings (AGC variants), to find the optimum solution for his application. The higher the AGC, the better noise is suppressed, but the lower the code compatibility. The devices contain a PIN diode and a preamplifier assembled on a lead frame. The epoxy package contains an IR filter. The demodulated output signal can be directly connected to a microprocessor for decoding. These components have not been qualified to automotive specifications. FEATURES • Individual IC settings to reach maximum performance • Immunity against noise (lamps, LCD TV, Wi-Fi) • Low supply current • Photo detector and preamplifier in one package • Supply voltage: 2.0 V to 5.5 V • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 APPLICATIONS • Infrared remote control systems DESIGN SUPPORT TOOLS • 3D models • Window size calculator BLOCK DIAGRAM 30 kΩ Input AGC Band pass Demodulator PIN 16833-22 Control circuit VS OUT GND Rev. 2.3, 16-Aug-2022 1 Document Number: 82459 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Datasheet Values Refer to PCN-OPT-1224-2022 www.vishay.com TSOP22.., TSOP24.., TSOP48.., TSOP44.. Vishay Semiconductors MECHANICAL DATA Pinning for TSOP44.., TSOP48..: 1 = OUT, 2 = GND, 3 = VS Pinning for TSOP22.., TSOP24..: 1 = OUT, 2 = VS, 3 = GND ORDERING CODE TSOP2..., TSOP4... - 2160 pieces in tubes APPLICATION CIRCUIT 17170-14 Transmitter IR receiver with TSALxxxx VS Circuit OUT GND R1 C1 VO + VS µC GND 1 2 3 23198 R1 and C1 recommended in case there are strong ripple or spikes on the supply line. PARTS TABLE AGC 30 kHz 33 kHz Carrier 36 kHz frequency 38 kHz 40 kHz 56 kHz Package Pinning Dimensions (mm) Mounting Application Best choice for Special options LEGACY, FOR LONG BURST REMOTE CONTROLS (AGC2) RECOMMENDED FOR LONG BURST CODES (AGC4) TSOP4830 TSOP2230 TSOP4430 TSOP2430 TSOP4833 TSOP2233 TSOP4433 TSOP2433 TSOP4836 TSOP2236 TSOP4436 (1)(2)(3) TSOP2436 (1)(2)(3) TSOP4838 TSOP2238 TSOP4438 (4)(5)(6)(9)(10) TSOP2438 (4)(5)(6)(9)(10) TSOP4840 (8) TSOP2240 (8) TSOP4440 TSOP2440 TSOP4856 (11) TSOP2256 (11) TSOP4456 (6)(7) TSOP2456 (6)(7) Mold 1 = OUT, 2 = GND, 3 = VS 1 = OUT, 2 = VS, 3 = GND 1 = OUT, 2 = GND, 3 = VS 1 = OUT, 2 = VS, 3 = GND 6.0 W x 6.95 H x 5.6 D Leaded Remote control (1) RC-5 (2) RC-6 (3) Panasonic (4) NEC (5) Sharp (6) r-step (7) Thomson RCA (8) Sony (9) Mitsubishi (10) Sejin 4PPM (11) Cisco • Narrow optical filter: www.vishay.com/doc?81590 • Wide optical filter: www.vishay.com/doc?82726 ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT Supply voltage Supply current Output voltage Voltage at output to supply Output current Junction temperature Storage temperature range Operating temperature range Power consumption Soldering temperature Tamb ≤ 85 °C t ≤ 10 s, 1 mm from case VS -0.3 to +6 V IS 5 mA VO -0.3 to 5.5 V VS - VO -0.3 to (VS + 0.3) V IO 5 mA Tj 100 °C Tstg -25 to +85 °C Tamb -25 to +85 °C Ptot 10 mW Tsd 260 °C Note • Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability Rev. 2.3, 16-Aug-2022 2 Document Number: 82459 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Datasheet Values Refer to PCN-OPT-1224-2022 www.vishay.com TSOP22.., TSOP24.., TSOP48.., TSOP44.. Vishay Semiconductors ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. Supply current Supply voltage Transmission distance Output voltage low Ev = 0, VS = 3.3 V Ev = 40 klx, sunlight Ev = 0, test signal see Fig. 1, IR diode TSAL6200, IF = 50 mA IOSL = 0.5 mA, Ee = 0.7 mW/m2, test signal see Fig. 1 ISD ISH VS d VOSL 0.25 - 2.0 - - 0.35 0.45 - 24 - 0.45 5.5 - 100 Minimum irradiance Maximum irradiance Test signal: RC5 code Ee min. - Test signal: NEC code Ee min. - tpi - 4/fo < tpo < tpi + 4/fo, test signal see Fig. 1 Ee.


TSOP2430 TSOP2433 TSOP2436


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)