Document
5.0SMDJ Series
Surface Mount – 5000W
TVS Diode Datasheet
RoHS Pb e3
Uni-directional
Bi-directional
Additional Information
Resources Agency
Accessories
Samples
Agency Approvals
Agency File Number E230531
Maximum Ratings and Thermal Characteristics (TA=25OC unless otherwise noted)
Parameter
Symbol Value Unit
Peak Pulse Power Dissipation at TL=25OC by 10/1000µs Waveform (Fig.2)(Note 1), PPPM 5000 W (Note 2)
Power Dissipation on Infinite Heat Sink at TL=50OC
PD
Peak Forward Surge Current, 8.3ms Single Half Sine Wave (Note 3)
IFSM
6.5 W 300 A
Maximum Instantaneous Forward Voltage at 100A for Unidirectional Only
VF
5.0
V
Operating Temperature Range
Storage Temperature Range
Typical Thermal Resistance Junction to Lead Typical Thermal Resistance Junction to Ambient
TJ -65 to 150 °C TSTG -65 to 175 °C
RƟJL
15 °C/W
RƟJA
75 °C/W
Notes: 1. Non-repetitive current pulse , per Fig. 4 and derated above TJ (initial) =25OC per Fig. 3. 2. Mounted on copper pad area of 0.31x0.31” (8.0 x 8.0mm) to each terminal. 3. Measured on 8.3ms single half sine wave or equivalent square wave for unidirectional component only, duty cycle = 4 per minute maximum.
Description
The 5.0SMDJ series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events.
Features & Benefits
■ 5000W peak pulse power
■ Typical IR less than 5μA when
capability at 10/1000μs
VBR min>22V
waveform, repetition rate (duty ■ High temperature to reflow
cycles):0.01%
soldering guaranteed:
■ SMD low profile surface
260°C/40sec
mount package minimizing PCB footprint
■ VBR @ TJ= VBR@25°C x (1+αT x (TJ - 25))(αT:Temperature
■ Typical failure mode is short
Coefficient,)
from over-specified voltage or ■ UL Recognized compound
current
meeting flammability rating V-0
■ Whisker test is conducted based on JEDEC JESD201A per its table 4a and 4c
■ Meet MSL level1, per J-STD-020, LF maximun peak of 260°C
■ IEC 61000-4-2 ESD 30kV(Air), 30kV (Contact)
■ ESD protection of data lines in accordance with IEC 610004-2
■ Built-in strain relief
■ Matte tin lead–free plated
■ Halogen free and RoHS compliant
■ Pb-free E3 means 2nd level interconnect is Pb-free and the terminal finish material is
■ Glass passivated chip junction tin(Sn) (IPC/JEDEC J-STD-
■ Fast response time: typically
609A.01)
less than 1.0ps from 0V to BV ■ Recognized to UL 497B as an
min
Isolated Loop Circuit Protector
■ Excellent clamping capability
■ Low incremental surge resistance
Applications
TVS devices are ideal for the protection of I/O Interfaces, VCC bus and other vulnerable circuits used in Telecom, Computer, Industrial and Consumer electronic applications.
Functional Diagram
Cathode
Bi-directional Uni-directional
Anode
© 2022 Littelfuse, Inc.
1
Specifications are subject to change without notice.
Revised: GD.06/29/22
5.0SMDJ Series
Surface Mount – 5000W
TVS Diode Datasheet
Electrical Characteri.