DatasheetsPDF.com

NSVA300 Dataheets PDF



Part Number NSVA300
Manufacturers New Japan Radio
Logo New Japan Radio
Description SAW FILTER
Datasheet NSVA300 DatasheetNSVA300 Datasheet (PDF)

NSVA300 Apr. 2013 NewJRC SAW FILTER Application Cordless telephone NSVA300 Electrical Specification: (Table 1) The device characteristics are measured in the circuit shown in Fig.1. Table 1. Electrical Specifications Item Spec. Typ. Input and Output Impedance - 50Ω Nominal Center Frequency (f0) - 914.5MHz Insertion Loss 913.3~915.7MHz 3.5dB max. 2.5dB Response Variation 913.3~915.7MHz 1.5dB max. 0.5dB Input and Output VSWR 913.3~915.7MHz 2.5 max. 1.8 Out of Band Rejection D.

  NSVA300   NSVA300


Document
NSVA300 Apr. 2013 NewJRC SAW FILTER Application Cordless telephone NSVA300 Electrical Specification: (Table 1) The device characteristics are measured in the circuit shown in Fig.1. Table 1. Electrical Specifications Item Spec. Typ. Input and Output Impedance - 50Ω Nominal Center Frequency (f0) - 914.5MHz Insertion Loss 913.3~915.7MHz 3.5dB max. 2.5dB Response Variation 913.3~915.7MHz 1.5dB max. 0.5dB Input and Output VSWR 913.3~915.7MHz 2.5 max. 1.8 Out of Band Rejection DC~<834.5MHz 55dB min. 65dB (Relative to Through Level) 834.5~872.9MHz 959.5~974.5MHz 45dB min. 30dB min. 55dB 50dB <974.5~1500MHz 55dB min. 65dB (Operating Temperature Range: -10~+60ºC) Maximum Rating: (Table 2) Table 2. Maximum Ratings Item Maximum Input Power Maximum DC Voltage Operating Temperature Range Storage Temperature Rating +20dBm 7.5V -10~+60ºC -25~+70ºC Mechanical Specifications: (Fig.2) Package is designed as small as 3.5x3.5x1.0[mm3] for SMD (Surface Mount Device) type. Notice: This part is electrostatic discharge sensitive and may be damaged by improper handling. http://www.njr.co.jp/products/device/index.html http://www.njr.com/products/device/index.html (Japanese) (English) IN 50Ω 1 87 2 SAW 6 345 OUT 50Ω NSVA300 Apr. 2013 (a) (1) Fig.1 Measuring circuit 3.5±0.2 (b) 3.5±0.2 J4X 14 (2) 1.0±0.2 (3) (0.95) 3 (0.6) 2 4 (0.8) [5x] 5 6 (1.0) [2x] 17 8 Fig.2 Package dimensions (in mm) 4.3 0.8 1.3 [6x] (0.6) [8x] Marking (1) Manufacture’s Mark (2) Lot Number (a) Year (b) Month *Oct.--Nov.--Dec.--(3) Part number Mark X Y Z Pin no. 1 2 3 4 5 6 7 8 Connection GND IN/OUT GND GND GND OUT/IN GND GND (2.54) (1.27) 0.8 [6x] 1.27 4.3 1.27 Via-Hole(Φ 0.3) Fig.3 Desirable land area (in mm) NSVA300 Apr. 2013 Notice 1. Use this component within operating temperature range. It might not be satisfied with electrical specification without operating temperature range. When it is used less than -10ºC or more than +60ºC, it might be a cause of degradation or destruction of the component. Even if it endures during a short time, it causes degradation of qualification. 2. When soldering iron is used, solder with the temperature at the tip of soldering iron: 350ºC max., the time of soldering: 10 seconds max., the power of soldering iron: 30W max.. 3. Notice that the allowed time of soldering with soldering iron is accumulated time, when soldering is repeated. 4. As rapid temperature change for cleaning after reflow soldering might be a cause of destruction clean this component after confirming that temperature of this component goes down to room temperature. 5. Confirm that there are not any influence for qualification to this component in mounting on PCB when this component is cleaned. 6. As it might be a cause of degradation of destruction to apply static electricity to this component, do not apply static electricity or excessive voltage while assembling and measuring. And do not transport this component with bare hand. 7. As it might be a cause of degradation or destruction to apply D.C. voltage between each terminal, apply D.C. voltage 7.5V max. in actual circuit. Note 1. This specification specifies the quality of this component as a single unit. Make sure that this component is evaluated and confirmed against this specification when it is mounted to your products. 2. The information contained herein may be changed without prior notice. It is therefore advisable to contact New Japan Radio Company before proceeding with the design of equipment incorporating this product. 3. The products are designed to be used with ordinary electronic equipment (data and communications equipment, office equipment, audio-video equipment, measuring instruments, etc). New Japan Radio Company does not assume any liability for the case using the products with the application required high reliability or safety extremely (such as space equipment, sea-bottom equipment, medical equipment etc). When intending to use any our product please contact our sales representatives in advance. Ins ertion Los s [dB ] Ins ertion Los s [dB ] NS V A300 Apr . 2013 S 21 0 FR E QUE NC Y C HAR AC TE R IS TIC S 20 40 60 80 100 C H1 : center 914.5 s pan 200 C H2 : center 914.5 s pan 200 S 11 S 22 0 2 4 6 8 10 Ins ertionLos s [dB ] VS WR VS WR S 11 11 9 7 5 3 1 814.5 S 21 0 F requency [MHz] 1014.5 S 22 11 9 7 5 3 1 814.5 20 40 60 80 100 0.3 F requency [MHz] F requency [MHz] 1014.5 3000 .


NSVA288 NSVA300 NSVA301


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)