DatasheetsPDF.com

MAX2010 Datasheet

Part Number MAX2010
Manufacturers Maxim Integrated Products
Logo Maxim Integrated Products
Description 500MHz to 1100MHz Adjustable RF Predistorter
Datasheet MAX2010 DatasheetMAX2010 Datasheet (PDF)

  MAX2010   MAX2010
19-2930; Rev 0; 8/03 500MHz to 1100MHz Adjustable RF Predistorter General Description The MAX2010 adjustable RF predistorter is designed to improve power amplifier (PA) adjacent-channel power rejection (ACPR) by introducing gain and phase expansion in a PA chain to compensate for the PA’s gain and phase compression. With its +23dBm maximum input power level and wide adjustable range, the MAX2010 can provide up to 12dB of ACPR improvement for power amplifiers operating in the 500MHz to 1100MHz frequency band. Higher frequencies of operation can be achieved with this IC’s counterpart, the MAX2009. www.DataSheet4U.com The MAX2010 is unique in that it provides up to 6dB of gain expansion and 21° of phase expansion as the input power is increased. The amount of expansion is configurable through two independent sets of control: one set adjusts the gain expansion breakpoint and slope, while the second set controls the same parameters for phase. With these settings in place, the linearization.






Part Number MAX2016
Manufacturers Maxim Integrated Products
Logo Maxim Integrated Products
Description LF-to-2.5GHz Dual Logarithmic Detector/Controller
Datasheet MAX2010 DatasheetMAX2016 Datasheet (PDF)

  MAX2010   MAX2010
www.DataSheet4U.com 19-3404; Rev 0; 9/04 KIT ATION EVALU E L B A AVAIL LF-to-2.5GHz Dual Logarithmic Detector/ Controller for Power, Gain, and VSWR Measurements General Description The MAX2016 dual logarithmic detector/controller is a fully integrated system designed for measuring and comparing power, gain/loss, and voltage standing-wave ratio (VSWR) of two incoming RF signals. An internal broadband impedance match on the two differential RF input ports allows for the simultaneous monitoring of signals ranging from low frequency to 2.5GHz. The MAX2016 uses a pair of logarithmic amplifiers to detect and compare the power levels of two RF input signals. The device internally subtracts one p.






Part Number MAX2015
Manufacturers Maxim
Logo Maxim
Description 0.1GHz to 2.5GHz / 75dB Logarithmic Detector/Controller
Datasheet MAX2010 DatasheetMAX2015 Datasheet (PDF)

  MAX2010   MAX2010
MAX2015 19-2998; Rev 2; 2/07 EVAALVUAAILTAIOBNLEKIT 0.1GHz to 3GHz, 75dB Logarithmic Detector/Controller General Description The MAX2015 complete multistage logarithmic amplifier is designed to accurately convert radio-frequency (RF) signal power in the 0.1GHz to 3GHz frequency range to an equivalent DC voltage. The outstanding dynamic range and precision over temperature of this log amplifier make it particularly useful for a variety of base station and other wireless applications, including automatic gain control (AGC), transmitter power measurements, and received signal strength indication (RSSI) for terminal devices. The MAX2015 can also be operated in a controller mode where it measu.






Part Number MAX2014
Manufacturers Maxim Integrated Products
Logo Maxim Integrated Products
Description 75dB Logarithmic Detector/Controller
Datasheet MAX2010 DatasheetMAX2014 Datasheet (PDF)

  MAX2010   MAX2010
19-0583; Rev 0; 6/06 50MHz to 1000MHz, 75dB Logarithmic Detector/Controller General Description The MAX2014 complete multistage logarithmic amplifier is designed to accurately convert radio-frequency (RF) signal power in the 50MHz to 1000MHz frequency range to an equivalent DC voltage. The outstanding dynamic range and precision over temperature of this log amplifier make it particularly useful for a variety of base-station and other wireless applications, including automatic gain control (AGC), transmitter power measurements, and receivedsignal-strength indication (RSSI) for terminal devices. The MAX2014 can also be operated in a controller www.DataSheet4U.com mode where it measures, compa.






Part Number MAX201
Manufacturers Maxim
Logo Maxim
Description +5V-Powered / Multichannel RS-232 Drivers/Receivers
Datasheet MAX2010 DatasheetMAX201 Datasheet (PDF)

  MAX2010   MAX2010
MAX200–MAX209/ MAX211/MAX213 +5V, RS-232 Transceivers with 0.1μF External Capacitors General Description MAX200-MAX209, MAX211, and MAX213 are a family of RS-232 and V.28 transceivers with integrated charge pump circuitry for single +5V supply operation. The drivers maintain the ±5V EIA/TIA-232E output signal levels at data rates in excess of 120kbps when loaded in accordance with the EIA/TIA-232E specification. The MAX211 and MAX213 are available in a 28-pin, wide small-outline (SO) package and a 28-pin shrink smalloutline (SSOP) package, which occupies only 40% of the area of the SO. The MAX207 is available in a 24-pin SO package and a 24-pin SSOP. The MAX203 and MAX205 use no external c.






500MHz to 1100MHz Adjustable RF Predistorter

19-2930; Rev 0; 8/03 500MHz to 1100MHz Adjustable RF Predistorter General Description The MAX2010 adjustable RF predistorter is designed to improve power amplifier (PA) adjacent-channel power rejection (ACPR) by introducing gain and phase expansion in a PA chain to compensate for the PA’s gain and phase compression. With its +23dBm maximum input power level and wide adjustable range, the MAX2010 can provide up to 12dB of ACPR improvement for power amplifiers operating in the 500MHz to 1100MHz frequency band. Higher frequencies of operation can be achieved with this IC’s counterpart, the MAX2009. www.DataSheet4U.com The MAX2010 is unique in that it provides up to 6dB of gain expansion and 21° of phase expansion as the input power is increased. The amount of expansion is configurable through two independent sets of control: one set adjusts the gain expansion breakpoint and slope, while the second set controls the same parameters for phase. With these settings in place, the linearization circuit can be run in either a static set-and-forget mode, or a more sophisticated closed-loop implementation can be employed with real-time software-controlled distortion correction. Hybrid correction modes are also possible using simple lookup tables to compensate for factors such as PA temperature drift or PA loading. The MAX2010 comes in a 28-pin thin QFN exposed pad (EP) package (5mm x 5mm) and is specified for the extended (-40°C to +85°C) temperature range. o o o o o o o o o o o o o Fea.



2010-05-31 : LP3971    SC6BA2    SC6BA4    SC6BA6    SC6BA8    MAX5090A    MAX5090B    MAX5090C    LTC7510    MCP1256   


@ 2014 :: Datasheetspdf.com ::
Semiconductors datasheet search & download site (Privacy Policy & Contact)